Having a reliable power backup system is essential in today’s world where electricity outages are common. Luminous inverters have gained popularity for their efficiency and durability. However, like any electronic device, they may encounter issues that require a reset to restore their functionality. In this article, we will guide you through the process of resetting a Luminous inverter, step by step.

Understanding Luminous Inverters

Luminous inverters are known for their ability to convert direct current (DC) power from batteries into alternating current (AC) power, which is used to run various electrical appliances during power outages. These inverters are equipped with advanced features such as overload protection, short circuit protection, and battery deep discharge protection.

Despite their robust design, Luminous inverters may encounter issues that can be resolved by performing a reset. Resetting the inverter can help resolve problems like abnormal behavior, error codes, or unresponsive controls. It is important to note that resetting the inverter should be done cautiously and only after ruling out other potential causes of the issue.

Step-by-Step Guide to Resetting a Luminous Inverter

Resetting a Luminous inverter involves a series of simple steps that can be followed by anyone, even without technical expertise. Here is a step-by-step guide to help you reset your Luminous inverter:

Step 1: Disconnect the Power Supply

The first step in resetting your Luminous inverter is to disconnect it from the power supply. This ensures your safety and prevents any electrical mishaps during the reset process. Locate the main power switch or unplug the inverter from the wall socket.

Step 2: Wait for a Few Minutes

After disconnecting the power supply, wait for a few minutes before proceeding to the next step. This allows the inverter to discharge any residual power and reset its internal circuitry.

Step 3: Check the Battery Connections

While waiting, it is a good idea to inspect the battery connections of your Luminous inverter. Loose or corroded connections can cause issues with the inverter’s performance. Ensure that the battery terminals are clean, tight, and free from any corrosion. If necessary, clean the terminals using a wire brush and tighten them securely.

Step 4: Reconnect the Power Supply

Once you have waited for a few minutes and checked the battery connections, it’s time to reconnect the power supply. Plug the inverter back into the wall socket or turn on the main power switch. Ensure that the power supply is stable and reliable.

Step 5: Power On the Inverter

After reconnecting the power supply, locate the power switch on your Luminous inverter and turn it on. The inverter should start up and display the necessary indicators or lights to indicate its operational status.

Step 6: Test the Inverter

Once the inverter is powered on, it is important to test its functionality. Connect a small electrical load, such as a low-wattage bulb, to the inverter’s output socket. If the inverter is functioning properly, the connected load should receive power and illuminate. Monitor the inverter’s behavior for a few minutes to ensure it remains stable.

Common Issues and Troubleshooting

While resetting the inverter can resolve many issues, there may be cases where additional troubleshooting is required. Here are some common issues that users may encounter with their Luminous inverters and possible solutions:

Issue 1: Inverter Not Turning On

If your Luminous inverter does not turn on after following the reset process, there may be an underlying issue. Check the battery voltage and ensure it is within the acceptable range. Low battery voltage can prevent the inverter from turning on. If the battery voltage is low, charge the battery and try again.

Issue 2: Error Codes Displayed

Luminous inverters are equipped with error codes that indicate specific issues. If you see an error code displayed on the inverter, refer to the user manual or contact Luminous customer support for assistance. They will be able to guide you through the specific troubleshooting steps based on the error code.

Issue 3: Overload or Short Circuit

If your inverter displays an overload or short circuit error, it may be due to excessive load connected to the inverter or a short circuit in the wiring. Disconnect all loads from the inverter and check the wiring for any signs of damage or short circuits. If the issue persists, consult a qualified electrician to inspect and repair the wiring.


Resetting a Luminous inverter is a simple process that can help resolve various issues and restore its functionality. By following the step-by-step guide provided in this article, you can reset your inverter safely and effectively. Remember to always prioritize safety and consult the user manual or contact customer support if you encounter any difficulties or error codes.


Q1: How often should I reset my Luminous inverter?

A1: Resetting your Luminous inverter should only be done when necessary, such as when you encounter issues with its performance or functionality. It is not recommended to reset the inverter regularly as it may disrupt its normal operation.

Q2: Can I reset my Luminous inverter while it is running?

A2: It is not advisable to reset your Luminous inverter while it is running. Always disconnect the power supply and wait for a few minutes before initiating the reset process.

Q3: Will resetting my Luminous inverter delete any settings or configurations?

A3: No, resetting your Luminous inverter will not delete any settings or configurations. It simply restores the inverter to its default state and resolves any temporary issues.

Q4: What should I do if the inverter still does not work after resetting?

A4: If your Luminous inverter does not work even after resetting, there may be an underlying issue that requires further troubleshooting. Refer to the user manual or contact Luminous customer support for assistance.

Q5: Can I reset my Luminous inverter without disconnecting the battery?

A5: It is recommended to disconnect the power supply and wait for a few minutes before resetting your Luminous inverter. However, if you are unable to disconnect the battery, you can try resetting the inverter by turning off the main power switch and waiting for a few minutes